皮卡车灯条-60英寸三色欧美皮卡转向刹车倒车灯条-皮卡专用灯条
价格
订货量(条)
¥45.00
≥1
店铺主推品 热销潜力款
䀋䀔䀏䀒䀌䀓䀐䀔䀓䀌䀑
在线客服
|
|
|
|
刹车、转向灯条、日行灯软灯条
LED芯片:三安贴片灯珠120灯,60黄 30红,30白
工作电压:12V
照射角度:180度 广角照射
颜色:白色 红色 黄色
适用插座:原车接头,无需改装电路。
产品特点:三重模式,刹车、转向、日行
。恒定LED驱动具有过载保护短路保护和过温保护。
规格:1.长152CM宽14mm厚6.5mm
2.长120CM宽14mm厚6.5mm
3.长90CM宽14mm厚6.5mm
4.长182CM宽14mm厚6.5mm
线序规格:
1,红色线日行灯正极
2,绿色线左转信号灯正极
3,黄色线右转信号灯正极
4,白色线常亮刹车信号灯正极
5,灰色线负极
灯条模式:5+1日间行车灯,5+2左转信号灯,5+3右转信号灯,5+4常亮刹车信号灯,5+2+3刹车信号灯
产品图片:
产品效果:
产品包装:
产品过程:
安装说明:
Product Parameters:
1.LED chip: San’an SMD3528&2835
2.Work Voltage:12V DC
3.Beam angle: 180 Degree
4.Color: White/Red/Yellow
5.Suitable Socket: Vehicle joint no need change anything.
6.Product Function: Brake Light. Turn Light. Running Lamp.
7.Size: L49"*W0.55"*H0.26" L60"*W0.55"*H0.26" L70"*W0.55"*H0.26"
Warning: The installation of this kit is recommended to be installed by a licensed professional .the improper installation of this kit will void all warranties.
Please read the following instructions thoroughly before installing it.
First using a tape measure, measure the lip under your trucks tailgate to ensure there is enough clearance to mount your tailgate light bar.
Following your trucks owner’s manual, carefully remove the tailgate from your truck.
Use the included 3M tape to temporarily mount the LED light bar to your trucks tailgate.
Using a 1/8thdrill bit, pre drill the four mounting holed into your trucks tailgate, this will make the following step much easier.
Securely mount the tailgate light bar to your truck using a drill and provided screws.
Run the power wire with flat 4pin connector behind your bumper and to your trucks flat 4pin connection. You may need to secure the slack in the wire so that it does not hang below the bumper.
If your purchased LED Tailgate light Bar with Reverse Light Option proceed with your installation using the flowing steps:
Carefully remove one of your tail light assemblies.
Power your truck on and pit it into reverse, So that your factory reverse lights are illuminated. It is imperative that you set the parking brake.
Return a volt meter, find the positive 12volt wire that powers your reverse light.
Using a volt meter , find the positive 12volt wire that powers your reverse light.
Once you have found your factory reverse light wire , use a wire stripper to cut and strip the wire.
Run the light bar’s whiter reverse wire to your factory reverse wire.
Use a butt connector to connect the tailgate bar’s white reverse wire to the trucks factory reverse wire. You can also solder or use a 3M tape connector to secure this connection.
Now you can re-install your tail light assembly and tailgate. And test your tailgate light bare to full functionality.
Please don’t connect it on the flasher of vehicle.
Flat 4 Pin Connector Diagram:
Red Wire: Running lamp, all White LEDs light up (5+1)
Green Wire: Left Turn Signal,left Yellow LEDs light up (5+2)
Yellow Wire: Right Turn Signal,right Yellow LEDs light up(5+3)
White Wire: Brake Lamp,all Red LEDs light up(5+4)
Gray Wire: Ground ( 5 )
相关产品: